Flipper Zero – 
📞 Contact: +91 995 500 3601|✉️ Email: training@craw.in
Flipper Zero is a versatile hacking companion for newcomers eager to explore from scratch and seasoned penetration testers alike. Its open‑source nature empowers cybersecurity pros to probe, analyze and breach multiple electronic devices under controlled conditions.
What Is Flipper Zero and How Does It Work?
Flipper Zero is a lightweight multi‑tool with a playful design that taps and breaches digital systems – from RF doors to NFC cards and GPIO‑driven hardware.
Being completely open‑source means you can re‑flash firmware, script new features, and iterate on community modules, turning it into the ultimate pocket‑sized playground for radio and hardware research.
Thanks to its affordable price and dolphin‑inspired UI, it’s equally attractive to hobbyists and professional red‑teamers who need a mobile lab on the go.

How Does It Work?
A built‑in 433 MHz antenna paired with a CC1101 transceiver allows Flipper Zero to transmit up to 50 m in open space, making it perfect for signal replay, brute‑force, and protocol analysis straight from your pocket.
Flipper Zero Tech Specs
MCU (microcontroller)
- Model: STM32WB55RG
- ARM Cortex-M4 32-bit 64 MHz (application processor)
- ARM Cortex-M0+ 32 MHz (network processor)
- Flash: 1024 KB
- SRAM: 256 KB
Display
- LCD Monochrome
- Resolution: 128×64 px
- Controller: ST7565R
- Interface: SPI
- Diagonal Size: 1.4“
Battery
- Li-Po 2000 mAh
- 7 days approximately
Sub-GHz radio module
- Chip: TI CC1101
- TX Power: 0 dBm max
- Frequency bands (depends on your region):
- 315 MHz
- 433 MHz
- 868 MHz
- 915 MHz
NFC
- Frequency: 13.56 MHz
- Supported cards:
- ISO-14443A/B
- NXP Mifare® Classic®, Ultralight®, DESFire®, etc.
- FeliCa™
- NFC Forum protocols
IR (infrared)
- Frequency: 125 kHz
- Modulation: AM, PSK, FSK
- Supported cards:
- EM400x, EM410x, EM420x
- HIDProx, Indala
GPIO
- 3.3 CMOS Level
- Input 5V tolerant
- Up to 20 mA per digital pin
Bluetooth LE 5.0
- TX Power: 0 dBm max
- RX Sensitivity: -96 dBm
- Data rate: 2 Mbps
MicroSD
- Up to 64GB MicroSDHC
- Read/Write speed: up to 5 Mbit/s
Buzzer
- Frequency: 100-2500 Hz
- Sound Output: 87 dB
- Type: Coin
Vibration motor
- Force value: 30 N
- Speed: 13500 rpm
Infrared
- TX/RX range: 800-950 nm
- TX power: 300 mW
iButton 1-Wire
- Operate modes: Reader/Writer/Emulator
- Supported protocols:
- Dallas DS1990A
- CYFRAL
Control
- 5-button joystick
- Back button
- Reboot — Back+Left buttons for 2 seconds
USB
- 1x USB 2.0 port, type C
- USB device
- Charging
Physical
- Size: 100 x 40 x 25 mm
- Weight: 102 grams
- Body materials: PC, ABS, PMMA
- Operating temperature: 0 ~ 40 °C
Coupon is instantly applied in your cart. Offer valid online until 31 Dec.
Discount appears right after checkout. Other coupons may be applied but the biggest discount wins.